賽特瑞? 智能實驗裝備供應商
集研發設計、銷售、售后維保專業服務商
聯系電話：
聯系電話：
熱搜關鍵詞： 氣氛管式電爐 高溫節能重燒試驗爐 型殼高溫透氣性測定儀 高溫抗折試驗機
產品型號：1650℃Max. High Temperature Hydrogen Atmosphere Box Furnace,(8x8x8＂, 8L)SMG MF1700X-H2
電爐類型：箱式電阻爐/箱式馬弗爐
電爐規格：
加熱溫度：
電爐系列：高溫馬弗爐
應用范圍：。
| Furnace structure | 、Double-layer stainless steel structure for maximum vacuum and safety. ?Water cooling front door and air cooling shell ?Built-in pressure gauge, vacuum valves, and two gas float meters ?Built-in H2 burning control system --- if the controller detects no flame in the burner, the gas delivery valve will be shut down automatically |
| Inside Chamber Size | 、Heated chamber: 200x 200x 200 mm (8x8x8 inch), 8 Liter 、Energy-saving 1800 grade fibrous alumina insulation 、High purity Al2O3 coating 、Warning: One Al2O3 fibrous door block is included. You must place the door block in the front the chamber to block heat radiation, otherwise, may damage seal ring at high temperature and cause hydrogen gas leaking |
Power | 7.5 KW |
Voltage | AC 208 - 240V single phase (50/ 60 Hz) |
Current | 30 Amp (50 Amp air breaker is required) |
Temperature | Continuous 1600°CMax. 1650°C(＜60min) |
Heating Rate | 5℃/ min |
Temperature Accuracy | +/- 1°C |
Thermocouple | two B type thermocouples (control thermocouple and secondary alarm thermocouple) |
Temperature controller | Main Temperature Controller is used for controlling the 30-segment heating program and provides the 1-level temperature alarm protection. Secondary Temperature Controller reads the temperature from the secondary B type thermocouple, monitors the temperature during all process and provides the 2-level temperature alarm protection. |
Pressure Control | 、The pressure sensor and pressure controller are installed. It reads the chamber pressure and controls the inlet and outlet gas valves respectively according to the pressure limit settings. 、The pressure control can be used to perform the following functions:PurgingPressure controlHigh and Low-pressure protection 、The pressure controllable range: -0.06 to 0.03Mpa. |
Heating Elements | 、6 sets of Mo coils heating elements are built-in and replaceable 、The heating element of Mo coil is consumable parts which should be ordered separately if extra is required. ( order pictured below left to order spare ) 、The heating element can be replaced by MsSi2 to run furnace under oxygen and air up to 1700℃(order picture below right to order spare) 、Warning: Mo heating element cannot be used under air or oxygen at the temperature gt; 300°C |
Temperature Control | ?FA-YD518P-AGtemperature controller is included. 、Proportional–integral–derivative control (PID control) and auto-tune function 、30 segments programmed with ramping, cooling and dwelling steps 、Built-in over-temperature alarm and thermocouple failure alarm 、+/- 1 oC temperature control accuracy 、Default DB9 PC communication port 、MET Certified |
Temperature controller (optional) | Temperature control software kit (for YD518P series controllers) + 15" laptop package is available at the options bar. Click for the detail information about the software kit. |
Eurotherm Nanodac Controller (optional) | 、A single one Eurotherm Nanodac Controller replaces all three original controllers in the furnace and performs advanced functions of:High accuracy temperature controlSecondary temperature monitor and alarmPressure control and alarmData acquisition/analysis and graphical recordingTCP/IP communications Eurotherm software includedA 15.6-inch screen laptop is included in the package. The Eurotherm software is installed and configurated. |
| Gas Flow Control and Vacuum Valve | 、Two large flow meters (N2: 0~3.5L/min, H2: 0~3.5L/min) are installed on the front panel of the furnace. 、One for purging Inert gas prior to introducing H2 gas 、One for controlling H2 gas flow 、One heavy-duty vacuum pump ( CE certified ) built-in bottom furnace. You may choose a UL certified pump at extra cost ( Pls click picture below to see specs) ( CE certified ) ( TUV certified ) |
| H2 Gas Burning Control Systemand Option Hydrogen detector | 、An ignition device already installed to incinerate flowing gas and detect burner temperature to ensure H2 burner is in working condition. If H2 does not burn properly, the controller will shut down the H2 gas delivery valve immediately. 、Warning: You must install a certified Hydrogen detector in operation facility to alarm hydrogen leaking b accident. If you can not find in a local store, please click the link below to order hydrogen detector from us at extra cost. ?Option Hydrogen detector to Enhanced safety for STR-Hydrogen Gas Tube Furnace |
| Water Cooling | A 58L/min recirculating water chiller is installed for cooling furnace sealing flange. |
Net Weight | 300Kg |
Overall Dimensions | 1200mmL×850mmW×1520mmH( without burner ) and 2020 H ( with burner ) |
Shipping Weight amp; Dimensions | 、Two Pallets 、1375 lbs, 54"x44"x89" 、320 lbs, 48"x40"x52" |
Warranty | One year limited warranty with lifetime support. (Consumable parts such as sample plates and heating elements are not covered by the warranty, please order the replacement at related products below.Attention: A free course of safety operation training at STR-field is required to purchase this furnace. A customer's side training is also available upon request at extra cost. If the users believe that they have sufficient experience and knowledge to handle the furnace in the dangerous or emergent situation, a liability release agreementmust be signed at the purchase. STR-Corp. is not responsible for any damages caused by misuse without safety operation training. Any damages caused by the corrosive and acidic gases are not under the coverage of the STR-One Year Limited Warranty. |
Compliance | 、CE Certified 、All electric components ( gt;24V) are UL / MET / CSA certified 、NRTL or CSA certification is available upon request at extra cost. （ please click mark below to learn details ) |
Application Notes | 、Please EXERCISE EXTREME CAUTION. H2 gas is highly flammable and explosive. H2 ignites at a temperature of 400°C, an explosion could occur when the hydrogen content reaches 4.0%-74. 2% in the air, please strictly follow the rules below to for safe operation. 、Inert gas MUST be used to purge the furnace chamber to eliminate all the air before introducing the H2 gas. ?The pressure inside the chamber should ALWAYS be controlled at around 0.01Mpa above during the entire heating process, otherwise, the oxygen in the air may backflow into the furnace chamber and cause the explosion in the worst-case scenario. ?Pressure over 0.02Mpa (Relative Pressure) is strictly prohibited. ?ALWAYS place the furnace in a room with a fume hood and a hydrogen detector installed. 、Good ventilation is necessary for the room in which place the furnace 、Exhausting Hydrogen gas in the room is forbidden. 、For preserving the longevity of the furnace components, we recommend the heating rate not to exceed 10 ℃/min. 、Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating. ? 、The refractory block must be inserted before the closing door. ?Please Click Underline to learn "Max. Working Temperature of Heating Elements of Tungsten, Tantalum, Molybdenum Under Various Processing Gases". 、Attention: A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to below 3 PSI for safe operation.Click here to learnthe installation of a gas regulator. |
Demo Video andOperation Instructions |
1200℃大口徑滑軌爐 管式快速退火爐 滲碳爐爐蓋總成 鐘罩式金剛石鋸片氫氣保護燒結爐
免責聲明：本站介紹內容（包括產品圖片、產品描述、技術參數等），僅供參考。可能由于更新不及時，或許導致所述內容與實際情況存在一定的差異，請與本公司客服人員聯系確認。 內容專業性較強，僅供參考學習，請勿直接采用。本站部分圖片和文字來源于網絡收集整理，僅供學習交流，版權歸原作者所有，并不代表我站觀點。本站將不承擔任何法律責任，如果有侵犯到您的權利，請及時聯系我們刪除。
洛陽賽特瑞高溫實驗爐Sintering Furnace始終致力于尖端高溫及加熱產品綜合解決方案。憑借整個集團雄厚的綜合實力、優秀的技術、完善的服務體系，成就了洛陽賽特瑞高溫實驗爐Sintering Furnace可靠的品質。我們生產的質量好，效率高，節能環保，深受國內外廣大客戶的歡迎。價格多少錢一臺? 需要根據詳細技術方案確定
是由供應商洛陽賽特瑞高溫實驗爐Sintering Furnace生產的,洛陽賽特瑞高溫實驗爐Sintering Furnace可以加熱到度
是由生產廠家洛陽賽特瑞高溫實驗爐Sintering Furnace生產的,可以聯系我們獲得電子版操作說明，以及遠程視頻指導
隨著國內企業生產研發以及高校科研的飛速發展，的需求量日益增加。廠家哪個好?銷售的公司不少，但購買的時候一定要特別注意，要選擇有真正實力，質量可靠，且有專業售后服務團隊的真正生產廠家。本生產廠家洛陽賽特瑞高溫實驗爐Sintering Furnace以高標準、高要求的研發生產理念，確保設備的可靠性！
外殼由冷軋鋼板折,表面經高速拋丸后靜電噴塑。
可拆卸組合面有密封墊、環、圈、帽。
推出新型設計方案，結構合理、通用性強、使用壽命高。
可按客戶要求定制。
洛陽賽特瑞高溫實驗爐Sintering Furnace目前共有90余種實驗室設備產品：高溫馬弗爐、、高溫管式爐、氣氛爐、真空爐、熱震爐、結晶爐、火試金爐、箱式爐，常規品足量半成品儲備，快至3個工作日發貨，定制品承諾按期交貨；可根據客戶對產品環境測試的需求，為客戶量身定制性價比高的解決方案及非標定制服務。
Phone
微信Wechat
郵箱Emailsaiterui#qq.com 
電話：
郵件：
